Blinking LED with Mblock and Arduino

We will blink the led with the mblock program. The list of materials that will be used in our led circuit before moving on to the codes of the application we will make with the Mblock program:

1-Arduino Uno

2-BreadBoard

3-LED

4-220Ω Resistor

5-Jumper Cables

We need supplies.

We add a 220 ohm resistor to the long leg of the Led that we added to our breadboard. We connect one leg of the resistor with a jumper cable to the digital pin 8 of our ardunio uno material (You can connect your jumper cable to any digital pin you want between 2-13). The circuit diagram is below.

Now let's come to our codes in mBlock;

In the Mblock program, we add the Arduino program starter code from the Robots menu. After adding the forever from the control menu, we add the code to whichever digital pin we connected our led to the inside of the "Robots menu ... we add the code to make the pin low. We write 8 because I connect it to digital pin 8. We do not light our led with the code of set digital pin 8 to low. After 1 seconds We make the digital pin no. high and make it light up. This event will be repeated constantly. In order to run these codes, after connecting our arduino board and circuit to the computer with a usb cable, first we select the Serial port from the Connect menu, let's choose the port to which our arduino board is connected from there. From the boards menu, Arduino Uno( or choose which board you are using) After selecting, select the Arduino mode from the Edit menu and click the Upload to Arduino button, we will send the codes we have written to our Arduino board and upload them. Thus, our program becomes ready to run.

To download the source code of the program CLICKHERE

To download the source code of the program CLICK HERE (This program ise done with mblock 5 version)

Note: You can upload the codes to the arduino uno board by pressing the connect and upload buttons at the bottom of the screen respectively.

In the Mblock program, we add the Arduino uno starts up code from the Events menu. After adding the forever from the control menu, we add the code to whichever digital pin we connected our led to the inside of the "Pin menu" we add the code to make the pin low. We write 8 because I connect it to digital pin 8. We do not light our led with the code of set digital pin 8 to low. After 1 seconds We make the digital pin no. high and make it light up. This event will be repeated constantly.

Comments

Pacman Game on Scratch Program

We will make an example of pacman game making with Scratch. Before starting the Pacman Game example that we will do with Scratch, we download the background for the pacman game from the internet and add it to the backdrop part in Scratch. When the background I downloaded was dark, I painted the dark colors with white. I made the borders thicker. After adding our background to our work, it came to creating the pacman character. I drew a full circle in yellow for the Pacman character. After that, I drew two lines towards the center using the line tool. I erased the remaining part with an eraser. If you want, you can use the erase background tool to erase between two black lines. Thus, our pacman character took his place with his mouth open. I created a guide dot right in front of the pacman character. This will keep us moving. I created a red dot. It's a little obvious, you can make this red dot smaller if you want, you can give it another color and make it more invisible. After cre...

How To Make Bubble Shooter Game on Scratch Program

We will make a bubble shooter game example with Scratch. I am adding 3 balloons and a target picture for the bubble shooter game we will make with Scratch. (You can increase the number of balloons). Now I come to the codes to be written inside balloon1. Let the number of balloons popped when the green flag is clicked is 0. Thus, the remaining numbers from the previous game are reset. Let the balloons be hidden at first. Then, it will appear in a random place between the coordinates we have determined at a random time between 1-5 seconds, wait for 2 seconds, then hide. X: The coordinates between -218/144 are the coordinates of the far left and the right of the screen, Y:134/-235 are the coordinates of the top and bottom of the screen. It will appear randomly in these ranges If our balloon is aimed and hit by the target; Balloon shot news is released. When this news reaches our balloon, the balloon will be hidden. Copy and paste the same code above. Then we say duplicate...

How to Make Countdown a Maze Game on Scratch

We will make a countdown maze game example with Scratch. For the countdown maze game example we will make with Scratch, we upload the maze picture we downloaded to our computer from the scene section to the scratch program. Then we select the object that we will move in the maze section from the choose a sprite section and add it to our scene. We bring the object to be moved to the red point, which is the starting point. First of all, we create a variable named Duration to calculate the elapsed time in the maze from the "Variables" menu When you click the green flag, set the duration variable to 40. Our goal is to get the ball to the finish line in 40 seconds. If our ball object to move, we give the x and y coordinates to go to the red starting point. Our object will not move only once. First of all, we add the "Forever" code from the "Control" menu so that it moves every time we press the arrow key. Now it's time to check which direction key is pres...

Scratch and Mblock With Arduino Examples

Search This Blog